MXR M300 Reverb + Gator 9V Power Combo & 3 Patch Cables

MXR M300 Reverb

Description

• Six meticulously crafted reverbs in one pedal
• Audiophile quality analog and digital audio paths
• Dry path is 100% analog • Studio-grade low noise floor • Trails Bypass mode lets effect ring out after turning the pedal off
• Expression pedal jack for foot control of all knob settings
• Stereo In/Out capability when using TRS cables

Power

The MXR Reverb requires 9 volts (240mA) and can be powered by the included Dunlop ECB003/ECB003EU adapter or the Iso-Brick Power Supply. This pedal cannot be powered by a battery.

Directions

• Run a standard instrument cable from your guitar to the M300’s INPUT jack and another cable from the M300’s OUTPUT jack to your amplifier. If using an expression pedal, run a TRS cable from the M300’s EXP jack to your expression pedal.
• Start with all controls at 12 o’clock.
• Turn the effect on by depressing the footswitch.
• Push in the TONE control to cycle through reverb styles, indicated by red or green LEDs in the LED column. See REVERB STYLES section for a description of each style
• Rotate DECAY control clockwise to increase length of reverb decay or counterclockwise to decrease it.
• Rotate TONE control clockwise for a brighter reverb sound or counterclockwise for a warmer reverb sound.
• Rotate the MIX control clockwise to increase reverb signal level or counterclockwise to decrease it. Fully clockwise results in an equal 50/50 mix of reverb and dry signals.

Controls

• EXP output allows blending of two setting configurations with an expression pedal (not included)
• FOOTSWITCH toggles effect on/ bypass (blue LED indicates on)
• LED column indicates selected reverb style
• DECAY knob sets length of reverb decay
• TONE knob shapes EQ of effect (or octave blend for PAD setting)and selects reverb style
• MIX knob sets reverb signal level

Reverb Styles

• PLATE : Classic studio plate reverb. Indicated by green LED.
• SPRING : Classic guitar amp reverb. Indicated by red LED.
• EPIC : Multiple interconnected modulated delays. Indicated by green LED.
• MOD : Modulated studio plate reverb. Indicated by red LED.
• ROOM : Simulates small room, early reflection slap-back sound. Indicated by green LED.
• PAD : Blend of octave down and octave up synth soundswith reverb effect. Indicated byred LED. Use TONE control toblend—fully counter clockwise provides one octave down andfully clockwise provides one octave up. The 12 o’clockposition provides both an octave up and an octave down. Use DECAY control to set synth pad and reverb decay

Using An Expression Pedal

• An expression pedal such as the DVP4 Volume (XL) Mini Pedal or the DVP3 Volume (X) Pedal can beused to toggle and sweep between two different setting configurations :
• Connect an expression pedal to M300’s EXP jack using a TRS cable, and set rocker to its heeldown position. Adjustknobs as desired. Note: Expression pedal cannot be used to change reverb style.
• Move rocker to its toe-down position. Adjust knobs as desired to a different setting configuration.
• Moving rocker back and forth will move effect sound smoothly between those two settings.

Stereo Mode

The M300 can be run in either Mono (default) or Stereo modes, selectable via internal switch, which determines tip/ring input connection. For a stereo setup, run a TRS splitter cable to the M300’s INPUT jack and another from the M300’s OUTPUT jack to your amplifier. Next, set internal STEREO/MONO switch to its LEFT position Note:When M300 is bypassed, output ring connection will only receiveignal if M300 is set to Trails Bypass mode (see below).

Advanced Functions –

Startup Mode

• Additional functions can be accessed by entering Startup Mode. Advanced function settings will remain in selected state, even after pedal is powered off. Re-enter Startup Mode and follow relevant steps to change settings again.
• Disconnect M300 from power supply and set DECAY and MIX controls to 12 o’clock.
• Enter Startup Mode by pushing down and holding TONE knob while connecting M300 to its power source.

Trails Bypass Mode

The M300 uses a “true bypass” relay by default, shutting off effectand hardwire bypassing the tipconnection signal as soon as you turn the pedal off (ring connection uses buffered bypass). TheM300 can also be operated using Trails Bypass mode, which uses a buffered bypass and allows the reverb effect to ring out even after you turn the pedal off.

• After entering Startup Mode, release TONE knob. LED column will now reflect bypass mode

STEREO MONO

• status. Green LEDs indicate factory-set True Relay Bypass mode, while red LEDs indicate Trails Bypass mode.
• Press TONE knob to toggle between modes.
• Depress footswitch to exit Startup Mode and resume normal operation.

Wet Mode

• The M300 can be set so that only the wet signal is sent to your amplifier.
• After entering Startup Mode, observe LED column for mode status. Green LEDs indicate factory-set Dry mode. Red LEDs indicate Wet mode.
• While still pushing down on TONE knob, rotate DECAY or MIX knob clockwise past 12 o’clock to select Wet mode,indicated by red LEDs. To return to Dry mode, rotate DECAY or MIX knob counterclockwise past 12 o’clock. Green LEDs will light up and red LEDs will turn off.
• Release TONE knob to save yours election and depress foots witch to exit Startup Mode and resume normal operation

Gator Cases GTR-PWR-1MAX 9V Power Supply Combo Pack

• 9V DC Power Adapter and 8-Output Daisy Chain Cable Combo Pack
• Slim Design Frees up Space on Power Strip by Occupying One Outlet
• Works with Optional Female-to-Male Daisy Chain Adapter Cable for Connecting Multiple Pedals
• Single Output Supplies Maximum of 1700mA to Power Fully Loaded Pedalboard
• AC Power Input with Variable Voltage Between 115V/230V (50-60Hz) for International Use
• 8-Foot Cable to Reach Far Away Outlets

Gator Cableworks Backline Series 6" Instrument/Patch Cable, 3-Pack

• 6-inch Instrument/Patch Cable, 3-Pack
• 1/4-inch Right Angle to 1/4-inch Right Angle
• Professional Low-Noise Cable
• Fine Stranded Oxygen Free Copper Conductor for High-Quality Signal Transmission
• Thick and Durable 6.5 mm Soft PVC Jacket
• Shrink Sealed Wire Connection for Protection and Strain Relief
• Reliable and Sturdy Connectors