Click to enlarge
Audio-Technica’s premium professional studiophones offer a flat, extended frequency response for professional studio monitoring. Superior components provide very high SPL capabilities while maintaining exceptional clarity of sound. Exterior design features include sturdy strain-relief cable and comfortable circumaural earpieces that can be rotated 180º to permit one-ear monitoring. The studiophones utilize 40-millimeter drives with neodymium magnets and copper-clad aluminum wire voice coils for lowest mass. They are equipped with an 11-foot cable terminated in a standard ¼-inch connector. This field-serviceable model allows elements, cables, and earpads to be replaced in the field if needed.
- Flat, extended frequency response for mixing/monitoring
- Field-replaceable cables, drivers and ear pads
- 1,600 mW of power handling, high SPL capability
- 40 mm diameter drivers, neodymium magnets and CCAW voice coils
- OFC litz wire cables, convenient one-side exit
- Rotating earpieces for easy one-ear monitoring
ART HeadAMP Four
Most home recordings involve from one to four people, any or all of whom are going to need headphone monitoring. The monitor amp would be connected to the tape deck's headphone output or a mixer output so that the performers can hear themselves and each other. Of course the same application can apply to band rehearsals and even home entertainment. HeadAmp 4 provides amplification and individual volume control for up to 4 headsets. It can be driven by either line-level or headphone amplifier signals (mono or stereo). The HeadAmp 4 sports a new case design (like USBPhono Plus), more features (added 1/8" I/O) and enhanced electronics.
Apex stereo headphones accurately reproduce the wide dynamic range associated with today's digital audio. The headphone speakers have been developed using the latest technology in driver design and materials and offer the frequency response and sound quality traditionally found only in much more expensive models. Three styles of Apex headphones fulfill any needs or preferences. Type Closed-back dynamic
Driver Diameter 40 mm
Magnet Neodymium
Voice Coil Copper-clad aluminum wire
Frequency Response 5 - 28,000 Hz
Maximum Input Power 1,600 mW at 1 kHz
Sensitivity 100 dB
Impedance 60 ohms
Weight 8.8 oz (250 g) without cable
Cable 11' (3.4 m) (OFC litz wire, left-side exit)
Connector 1/4" (6.3 mm) phone plug Specifications and product details are subject to change without notice.
Microphone Conditions (Additional comments)
Open Circuit Sensitivity At 1 kHz, with 1 Pa (Pascal) = 94dB sound pressure level (SPL), measured at diaphragm. Stated in dB re 1 volt, and in millivolts.
Noise, typical A-weighted, using Audio Precision System One measurement system.
Weight Stated for the microphone only, without accessories, and without attached cable/power module, if applicable.
Frequency Response (Graph) Shows mic output versus frequency with a constant sound input level from a source 0.5 meters from the diaphragm. Each vertical division in the graph is 10dB. A dashed line, if present, shows the effect of a low-roll-off (hi-pass) function.
Polar Pattern (Graph) Shows mic output versus angular direction of the sound source, with a constant sound input level at 1 kHz, at a constant distance from the diaphragm. Zero degrees (0°) is the "front" of the mic. Each circular division in the graph is 5 dB, beginning from the 0° point and counting inward.
Additional Information Profile pages for some products provide links to additional information, such as further specifications, operating instructions, product reviews, etc. These may be in various forms, such as text, graphics and pdf files.
Related Models Some profile pages provide links to other models of a most-similar or closely related type or function that may also be of interest.
Headphone/Headset Conditions (Additional comments)
Headphone Sensitivity Input of 1 milliwatt at 1 kHz into rated impedance; output in dB SPL, using a Brüel & Kjaer 4153 coupler.
Maximum Input Power At 1 kHz into rated impedance.
Boom Mic Sensitivity Open circuit, at 1 kHz, with 1 Pa (Pascal) = 94dB sound pressure level (SPL), measured at diaphragm. Stated in dB re 1 volt, and in millivolts.
Additional Information Profile pages for some products provide links to additional information, such as further specifications, operating instructions, product reviews, etc. These may be in various forms, such as text, graphics and pdf files.
Related Models Some profile pages provide links to other models of a most-similar or closely related type or function that may also be of interest.
ART HeadAMP Four Signal To Noise Ratio- >90dB
*IMD (SMPTE)- 0.01%
*Maximum Input Level- +14dBV
*Maximum Output Level- 20dB per channel
*Output Impedance- 51 Ohms per channel
*Output Connectors- Four stereo 1/4? headphone outputs
*Power Requirements- 12V DC (Adapter included)
*Total Harmonic Distortion- <0.01%
*Power- Power on LED
*Dimensions- 4.5x2.875x1.5 inch (150mm x 75mm x 38mm)
*Weight- 1.3 lbs. (590g)
|
|
Price: $72.00
WE WILL GO LOWER!
or call us at: 1-888-890-6222
|
|
|
Manufacturer
|
Audio Technica
|
|
Unit |
|
|
SKU |
1001
|
|
|
